IAG STAGE 4 EXTREME EJ25 CLOSED DECK CASE - 14MM H.S.M., FIRE-LOCK, PINNED + LINE HONED, ARP CASE BOLTS, (NO BORE / HONE) - FOR SUBARU WRX, STI, LGT, FXT
Lease for as low as $/week
The Stage 4 Extreme is IAG's strongest and most prepared EJ25 Closed Deck offering. The case halves are split and the main webs are CNC machined in our Haas VF-4SS CNC mill for 9.5mm pins to reduce distortion and movement of the case in extreme conditions. The case halves are then reassembled and IAG machines the case to accept the IAG CLOSED Deck Inserts that transform the block into a solid deck. The unique inserts feature small passages that allow needed coolant flow to the deck surface. The case halves are then CNC machined for our new Fire-Lock head gasket solution that is loosely derived from diesel technology where a counterbore step is machined around each cylinder bore allowing specially sized fire rings to drop into the machined area and head gasket bores. The Stage 4 Extreme case is CNC drilled and tapped to fit 14mm head studs. Utilizing the new Fire-Lock gasket solution along with larger IAG / ARP 14mm head studs, nuts, and washers reduce the chances of the heads lifting under extreme boost conditions. Finally, ARP case bolts are installed and torqued before line honing the completed case in our in-house Sunnen CH-100 machine. IAG’s Closed Deck is suitable for street or race use and has been tested in vehicles producing 1000+ horsepower and over 55psi of boost.
What is a Closed Deck Block and why do I need it?
The factory Subaru EJ25 case is referred to as a semi-open (or semi-closed) deck. The block is essentially an open deck with 3 narrow supports tying in the main case to the tops of the sleeves. This feature was a slight improvement over the EJ20 case, which was a completely open deck with no support. The purpose of the deck supports is to keep the sleeve from moving. While conceptually this is an improvement, the reality is that it simply isn’t enough for a high horsepower Subaru. The weakest point of the sleeve is still left open and unaddressed.
What is unique about IAG’s Closed Deck process?
Our machining process converts the semi-open deck to a complete closed deck and uses threaded plugs to provide additional support at the case bolt access positions. This innovative design is just one of the features that set our conversion apart from others on the market. Another innovative feature is the use of cast insert material that closely matches the metallurgy of the aluminum case material in a factory Subaru EJ engine block. By using a similar cast material (rather than billet), we ensure that during expansion and contraction the materials grow and shrink at similar rates, which is vital for maintaining roundness within the top of the bore. The outer inserts are machined from ¾ inch cast material and the inner inserts from 1” cast material. Once the deck is surfaced, the result is a true ½ inch finished outer insert thickness and true ¾ inch finished inner insert thickness.
What is IAG’s Stage 4 Extreme Closed Deck Process?
The IAG Closed Deck conversion is performed 100% in-house by our engineers and experts using state-of-the-art equipment. The IAG Closed Deck starts with a new OEM EJ25 bare case. The case is loaded and fixtured to a 4th axis rotary indexer in our 2015 Haas VF-4SS CNC Vertical Machining Center. It is supported at the main journals using a precision ground 2-inch bar and tailstock which ensures the datum is the main journals. This method gives us a true reference point to perform all machining operations. A Rennishaw probe is utilized to check that the case is fixtured true and once confirmed the machining process begins.
Once the case is fixtured, the first step is to mill out 12 pockets for CNC inserts. Rather than attempting to install inserts into an inconsistent cast case, the pockets are milled out to exact dimensions creating a consistent area that accepts our precision inserts. Once the pockets are machined, the case is removed from the mill and placed into a block oven at a low temperature. Our pre-machined closed-deck inserts are simultaneously chilled using dry ice. When the case and inserts have reached our desired temperature, they are moved into our install station, which holds the block and lightly presses the inserts into position on one side of the deck surface. This process is repeated on the other side and then the partially completed case is moved to a cooling rack.
In the next step of our process, the case is loaded and fixtured back into the VF-4SS after reaching room temperature. During this stage, the flanges left from machining the inserts are milled close to the case deck surface. Features such as coolant passages and case bolt access positions are machined in preparation for the final stages of our conversion process. Specially machined, threaded case bolt plugs utilizing a 3/8 inch square drive are installed and torqued into place. Once they are torqued a ½ inch square drive is machined into each to allow coolant to properly flow and ensure that the thickest part of the plug is supporting the weakest area of the case.
Each deck surface is then machined true and flat using a Poly Crystal Diamond insert. Finally, we engrave each plug for location and indexing. This step ensures that the plugs are installed in the correct position and rotation after the block is assembled.
What's Included:
- (x1) IAG Stage 4 Extreme Closed Deck converted EJ25 Case (Starts as brand new OEM Case 99.5mm)*Bore and hone additional and required before final assembly!
- (x8) Threaded case bolt plugs
- (x1) Machined for 9.5mm pinned mains
- (x1) ARP Case Bolt Set
- (x1) Line Honed Mains
- Fire-Lock - IAG Fire-Lock receiver groove machining, latest solution to prevent head gasket failure on high horsepower and high boost Subaru's - *IAG Fire-Lock head gaskets required
- (x1) Machined for 14mm Head Studs (14mm Head Studs sold separately)
Additional Options:
- (x1) IAG / ARP 14mm Head Stud Set - $550.00
Head Gasket Required:
- *IAG Fire-Lock .051" Head Gaskets with IAG-Spec Alloy Ring Set* PN# IAG-ENG-1740
Please Note: Overbore must be performed (99.75mm is the preferred bore) before assembly!
If using on 2002-05 Subaru EJ20 2.0L WRX additional modifications and parts are required.
Fitment-
2002-2014 WRX
2004-+STI
2005-2009 Legacy GT
2004-2013 Forester XT
*Attention: Special note about using ARP Case Bolts - IAG installs ARP CASE BOLTS with 30W engine oil using OEM SUBARU torque specs and procedures. Other torque specs and lubricants may lead to case distortion damage.
*Pictures used for marketing purposes only, actual product may vary
Returns may be accepted within 14 days of purchase pending Return Merchandise Authorization (RMA). No returns or cancellations on special order items. All returns will be charged a 20% restocking fee, no exceptions.
To be eligible for a return, your item must be unused and in the same condition that you received it. It must also be in the original packaging. Item must be able to be resold as new.
Several types of goods are exempt from being returned. Hazardous materials, fluids, greases, chemicals, and clothing are not able to return.
Free shipping is available within the lower 48 states for most orders totaling $199 or more. A free shipping option will be available during checkout. This offer is for delivery address in the continental United States and excludes shipments going to Alaska, Hawaii, Military Boxes, and items that require freight shipping.
Processing Time
Patterson Performance stocks a large quantity of items at any given time. Some items may require drop shipping from one of our various distributors. In stock items will ship within 1-2 business days. If you're needing your product quickly, please contact us to verify product availability before placing your order. Orders requiring additional verification (security concerns, incorrect information, etc.) may need additional processing time. Estimated shipping dates are not guaranteed and are subject to change based on inventory levels and manufacturer lead times. Backordered items are shipped immediately once available.
Items ship daily, If the item you ordered is not in stock, a member of our team will contact you via email / phone.
Patterson Performance will only ship to an address that varies from your billing address if payment is made via Paypal or a financing partner.
Patterson Performance ships from multiple warehouses throughout the United States, and sometimes from manufacturers overseas.
You can simply contact us via email / telephone for a live inventory check
Find more information at www.P65Warnings.ca.gov.
